- Product Details
-
ULTRASONIC CLEANER SPEC
FEATURES
Degas function to increase the cleaning effect
Automatic tracking of ultrasonic frequency
Configurable temperature
User-friendly controls
LED indication of temperature and time values
Memory function
High performance transducers
Thank you for purchasing the CINOFIBER ultrasonic cleaner. Please take the time to read these operating instructions before use and retain them for future reference. Failure to follow these instructions may lead to serious personal injury and damage to property.
INTRODUCTION
UItrasonic cleaning works by transmitting high-frequency sound waves (40 kHz in this product) through a liquid.The sound waves agitate the liquid and create microscopic cavitation bubbles.These bubbles implode with sufficient force to scrub clean the surface of any item placed in the cleaner.
The microscopic bubbles will penetrate the smallest cavities in items which require cleaning, which makes ultrasonic
cleaning much more efficient than manual processes.
Ultrasonic cleaning is suitable for cleaning a wide variety of materials including metals, glass, rubber, ceramics and some hard plastics.
Examples of contaminants which can be removed by ultrasonic cleaning are dust, dirt, oil, grease, pigments, flux agents, fingerprints and polishing compound.
Ultrasonic Cleaning Priciple
PREPARATION
- Unpack the ultrasonic cleaner and remove all packaging materials. Visually inspect the unit for any transit damage prior to use.
- Ultrasonic cleaner
- Ultrasonic cleaner
Contents:
- Sound proof lid
- Power cord (US plug with 120 V a.c.models, EU and UK cords with 230 V a.c.models)
- Outlet filter
- Mesh basket
- User manual
- Place the ultrasonic cleaner on a flat, clean surface and ensure that the cooling fans are unobstructed. Ensure the drain tap is in the closed position.
- Connect the power cord to the ultrasonic cleaner and then to a suitably rated electrical outlet. See specification table for the electrical requirements specific to your model.
- Carefully fill the tank to a minimum of 1/2 volume with the chosen solvent solution. Take care not to exceed the maximum fill level. For more demanding cleaning (of oil and grease), a small amount of washing up liquid can be added to the solution. The ultrasonic cleaner is now ready for use.
- Turn the equipment off (on the unit and at the wall socket);
- Turn the equipment off (on the unit and at the wall socket);
Attention
In normal use,the ultrasonic cleaner will emit a constant sound and the surface of the liquid will be stable other than a limited spray which is created by the cavitation bubbles.
If there are discontinuous surges in the liquid, add or remove solvent as required to ensure surface stability. This will aid in efficient cleaning.
When the cleaning process is completed,
- Remove the lid;
- Carefully remove the basket.
CAUTION-the lid, basket and cleaned items could be up to+80 ℃
DRAINING AND CLEANING THE TANK
To drain the tank after use:
- Isolate from the mains supply and remove the power cord
- Remove the lid and any items in the tank
- Ensure that the liquid has cooled sufficiently and tip the unit to empty the tank.If the unit has a drain valve,this can also be used to empty the liquid. Ensure that the drain valve is closed immediately after draining.
- Dispose of the liquid in accordance with local regulations
- The tank should be cleaned with water and mild detergent. Do not use abrasive cleaning methods.
OPERATION GUIDELINES
Step
Action
1.
Follow the instructions described in the PREPARATION section
2.
Place the items which require cleaning into the basket
Slowly lower the basket into the tank
Ensure that items are not touching each other or the bottom of the tank. Ensure items are fully submerged in the solution
3.
Switch the equipment on at the electrical socket and on the back of the unit The display will show the current ambient temperature
The time and temperature settings will default to their last values.
Timer
Set the cleaning time by pressing below buttons as required.
The timer will count down to 00:00 at which point the cleaning function will stop Note: Do not exceed the maximum continuous operating period of 60 minutes.
Heating
Press below button to start or stop the heating function.
Use the buttons to set the desired temperature.
A temperature between 40°C and 60°C is recommended
If the selected temperature exceeds the current liquid temperature, the heating function will be active and the indicator above the button will be illuminated.
ULTRASONIC SWITCH
After setting the desired time and temperature, press below button to activate /deactivate ultrasonic mode.
When active, the timer will countdown
This mode uses maximum ultrasonic power.
SAFETY PRECAUTIONS
Please read the following instructions very carefully. Failure to follow this guidance may result in personal injury, property damage or invalidate the product warranty.
If the ultrasonic cleaner is not used in a manner described in this manual or is used with accessories which are not recommended by CINOFIBER the protection provided may be impaired.
There are no user-serviceable parts inside the equipment. Do not remove the covers.
This equipment should only be operated by trained professionals.
Electrical
THIS EQUIPMENT MUST BE EARTHED
Ensure that the mains electrical supply socket is located close to the unit and is easily identifiable and accessible to users.
lf the power cord requires replacement, ensure that a suitably rated replacement is used. If In Doubt, Consult A Qualified Electrician.
Do not immerse the unit or power cord in water or any other liquid. If the equipment becomes wet, disconnect from the supply immediately.
Do not operate the unit or disconnect from the electrical supply with wet hands.
Always disconnect from the electrical supply prior to filling or emptying the tank.
General
Only use water-based cleaning solutions. Never use alcohol, gasoline or other flammable solutions. Strongly acidic or alkaline cleaning agents could cause corrosion of the equipment. Dilute these substances to a low level before use.
Do not run the cleaner continuously for over 60 minutes.
Always operate with liquid in the tank between 1/2 full and the maximum fill level.
Do not drop items into the tank as this could cause damage or spillage. Use the basket to hold items and carefully lower into the liquid.
Do not overload the basket. To ensure an efficient cleaning process, items to be cleaned should not touch each other and should be fully surrounded by the liquid.
Always fit the lid during use to prevent splashes and evaporation.
The cleaning solution could be hot (up to+80°C)take care when adding or removing items.
Ensure that the equipment is placed on a stable, clean surface and that the ventilation openings are not blocked.
Always isolate the equipment from the electrical supply when the cleaning cycle is complete.
Drain the equipment of cleaning solution before moving.Always use the carrying handles if fitted to your specific model.
FRONT PANEL
A: LED display temperature.
B: LED display cleaning time.
C: Heating button: Press this button for start/stop heating.
(Note:1: The new machine will display the ambient temperature when first time use.)
D: Increase Temperature:
Press this button to set the temperature.
Press once to increase 1°C,holding the key to increase by 10℃
E: Temperature reduce:
Press this button to set the temperature.
Press once to reduce 1°C,holding the key to reduce by 10°℃ .
F: Degas: Press button to engage /disengage'normal'mode.
G: Timer increase : Press this button to set the cleaning time
Press once to increase 1minute,holding the key to increase
by 10minutes
H: Timer reduce: Press once to reduce 1minute,holding the key to reduce by 10minutes.
FUSE REPLACEMENT
- Isolate the equipment from the electrical supply and remove the power cord;
- Drain the liquid from the tank. CAUTION-wait until the liquid has cooled to a suitable temperature before draining;
- Open the fuse drawer in the IEC electrical inlet on the back of the equipment. A flat-bladed screwdriver can be used to do this;
- Remove the fuse drawer and replace the fuse. Ensure that a correctly rated fuse is fitted (see specification table)
- Refit the fuse drawer and recommission the equipment following the instructions given in the PREPERATION section
- If the fault persists, withdraw the equipment from service and contact CINOFIBER for guidance
- Unpack the ultrasonic cleaner and remove all packaging materials. Visually inspect the unit for any transit damage prior to use.
Ultrasonic Cleaner
Category:
Key Words:
Factory Environment
Cinofiber will continue to be a leader in the optical communication industry, providing customers around the world with more stable, reliable, and high-quality products and services.
Questions And Answers
网站的定期维护工作有哪些？
定期的网站维护工作是保证网站安全、稳定运行和用户体验的关键。维护工作包括更新网站内容、检查和修复网站链接、备份数据、定期进行安全检查，修复漏洞，优化性能等。这些工作有助于确保网站长期有效运行并提供良好的用户体验。
网站设计中的UI和UX有何不同？
UI（用户界面）和UX（用户体验）是网站设计中两个重要的方面。UI着眼于网站的外观设计、布局和视觉元素，而UX注重用户在网站上的整体感受和互动体验，包括易用性、导航、交互等。优秀的UI设计通常会提升用户的UX体验。
网站托管服务有哪些类型？
网站托管服务可分为共享主机、虚拟专用服务器（VPS）、独立服务器和云托管。共享主机是多个网站共用一台服务器资源，VPS是虚拟专用服务器，独立服务器是专属服务器，而云托管基于云服务提供托管解决方案，每种类型都有不同的特点和适用场景。
网站流量统计工具的作用是什么？
流量统计工具如Google Analytics帮助分析网站访问数据，包括访客来源、访问量和用户行为等。通过了解这些数据，网站所有者可以了解受众，调整网站内容和设计，提升用户体验，增加转化率。
如何选择适合自己的网站建设技术？
选择网站建设技术需要根据个人技术水平和网站需求。如果熟悉编程，可以选择使用HTML、CSS、JavaScript等编写自己的代码。另外，也可考虑使用现有的框架或库，如Bootstrap、React等，简化开发流程。
如何开始建立自己的网站？
建立网站首先需要选定一个域名，这是网站的地址。然后选择合适的主机服务商，主机是存放网站文件和数据的地方。接下来编写网站代码或设计页面，最后将网站文件上传至服务器。这样网站就可以在互联网上被访问和浏览了。
Certificate Of Honor
Message Inquiry
Please leave your contact information so that we can contact you as soon as possible!
The technical team has 20 years of experience and accumulation
CONTACT US
Name: Lee
Position: Sales Engineer
Phone: +86 17896638805
WhatsApp: +86 17896638805
WeChat: +86 17896638805
Email: lee@cinofiber.com
CONTACT US
Name: Owen
Position: General Manager
Phone: +86 13670275731
WhatsApp: +84 93 787 40 07
Email: owen@cinofiber.com
Powered by: CEglobal